Wood - Database

The Wood Database may be accessed from the Wood tab of the Section Sets spreadsheet by clicking in the Shape field and then clicking , or by clicking the Shape Database button on the Advanced ribbon and then clicking the Wood tab of the Shape Database window.

Click on image to enlarge it

Wood Material/Shape Selection

Unlike any other material, the design properties for wood members depends both on the material selection as well as the shape selection. Therefore, the Wood tab of the Shape Selection database contains shape and material selections.

Material Selection

The ‘Material Selection’ menu reads in material options that are currently listed on the Wood tab of your Materials spreadsheet. You can select one of these existing materials, or click on the Create/Edit Wood Material button to open the Create/Edit Wood Material window, which lets you add a new material, or edit an existing material, without having to go to the Materials spreadsheet.

Create/Edit Wood Material Window

The Create/Edit Wood Material window lets you create or edit a material that is then automatically added to your Materials spreadsheet. This allows you to enter/select this information directly from the Draw Members Property Panel without having to first manually enter the information in the Materials spreadsheet.

Click on image to enlarge it

To create a new custom wood material:

1. Choose Custom from the Wood Type drop down.

2. Click the New button to manually enter the design values for a new custom wood material.

This information will then be automatically saved to the Custom Wood Species spreadsheet.

Size Selection

Currently there are two ways to define a member size. In the Shape Type dropdown the options available are from either the defined list of Nominal Sawn Lumber sizes, or by using the Net Rectangular/Round option (typically referred to as Full Sawn).

• The Nominal Sawn Lumber option populates a list of nominal sized shapes for the NDS design code and a list of net sized shapes for the CSA O86 design code. When the NDS design code is chosen, the program automatically reduces the shape properties to their net sizes. If the CSA O86 design code is selected, a list of actual metric sizes are shown.
• Either the Net Rectangular or Net Roundoption lets you manually enter any dressed size that you like.
  • Rectangular imperial full sawn (as opposed to nominal dimensions) shapes will be designated with a "FS" suffix. You can also use this nomenclature to type the size directly into the spreadsheet. For example, a 7.25"x12" net rectangular member can be typed in as "7.25x12FS".
  • Rectangular metric full sawn (as opposed to nominal dimensions) rectangular shapes will be designated with a "MFS" suffix. You can also use this nomenclature to type the size directly into the spreadsheet. For example, a 184mmx305mm net rectangular member can be typed in as "184x305MFS".
  • Round imperial shapes will be designated with a "RND" suffix. You can also use this nomenclature to type the size directly into the spreadsheet. For example, a 10" net round member can be typed as "10RND".
  • Round metric shapes will be designated with a "MRND" suffix. You can also use this nomenclature to type the size directly into the spreadsheet. For example, a 254mm net round member can be typed as "254MRND".

View Design Properties

Once you have selected the appropriate member size and material, you can view the un-adjusted wood design values (Fb, Fv, Ft, etc.) for the selected combination in the Properties table at the bottom of the window. The final adjusted values (Fb', Fv',Ft', etc.) will then be displayed after solution in the Member Detail Reports.

Wood Database Limitations

Round Shapes

Per section 3.7.3 of the NDS, the design of a round cross section shall be based on the design calculations for a square shape with the same cross-sectional area. Therefore the moment of inertia values will be calculated per the equivalent square shape, not the round cross section. However, the section modulus value, S is calculated per the actual round shape.

Glulam Databases

The program includes five tables of available glulam materials: NDS Tables 5A - 5D and CSA O86 Table 6.3. The values in NDS tables 5B & 5D depend on the number of laminations in the glulam. Therefore you will see three listings (2 Laminations, 3 Laminations, or 4 Laminations) for each material. If you have a custom material that is not available from these lists, you can always enter your appropriate design values as a Custom Wood Material for use in your model.

Mechanically Graded Lumber

Mechanically graded lumber grades (MSR & MEL) are available for use with the ANSI/AWC NDS-2015 and the CSA O86-2014 design codes. Older versions of the design codes will not support design of mechanically graded materials from the program databases. However, you can always enter the properties as a Custom Wood Material to get the design calculations for these materials in older code versions.

Click on image to enlarge it

In order to assign a mechanically graded lumber material, you must select both the species and then the mechanical (MEL or MSR) grade. The species selection determines the shear capacity and compression perpendicular to grain capacity design values.

See Footnote #2 from NDS 2015 Table 4C which says that all species from NDS 2015 Table 4A are applicable. See clause 6.3.2 from CSA O86-14 which says that specified shear strengths shall be taken from CSA O86 Table 6.3.1A.

The other design values are defined per the mechanical grade. See NDS 2015 Table 4C and CSA O86-14 Tables 6.3.2 and 6.3.3.

Structural Composite Lumber (SCL)

Each SCL manufacturer has documentation of their proprietary material design values. Because these are updated so often, RISA-3D relies instead on the design data from approved product reports (APA and ICC-ES) to build the material databases:

Footnote Limitations:

Each of the above reports includes tables with design values which were used to create the RISA-3D and RISAFloor SCL design property material databases. However, due to the difficulty of design variation, the following limitations are present:

• The Fb design values are not factored in accordance with the depth of the member. Currently RISA-3D always uses the single tabular Fb value regardless of member size.
• The Ft design values are not factored in accordance with the length or thickness of the member. Currently RISA-3D always uses the single tabular Ft value regardless of member size.
• The Fb design value will be increased by 4% if the member is designated as a repetitive member using the Cr check-box on the Wood tab of the Members spreadsheet.

Alternatively, you can always enter the appropriate design values, per the applicable footnotes, as a Custom Wood Material.

Design Values

The design properties may be verified by clicking on the ellipsis next to the Material section of the specific member's information in the Property Panel.

Click on image to enlarge it

The values are as follows:

• Fb_joist: Bending capacity due to joist/beam edge loading
• Fb_plank: Bending capacity due to plank/flat edge loading
• Fv_joist: Shear capacity due to joist/beam edge loading
• Fv_plank: Shear capacity due to plank/flat edge loading
• Fc_joist: Compressive (perpendicular to grain) axial capacity due to joist/beam edge loading
• Fc_plank: Compressive (perpendicular to grain) axial capacity due to plank/flat edge loading
• Fc: Compressive (parallel to grain) axial capacity, regardless of load direction
• Ft: Tensile axial capacity, regardless of load direction
• E_joist: Modulus of elasticity due to joist/beam edge loading
• E_plank: Modulus of elasticity due to plank/flat edge loading
• E_mod: Young's Modulus modifier (always set as 1.0)
• COV_E: Coefficient of Variation in Modulus of Elasticity per NDS Table F1. This value is used in the Emin calculation. For SCL materials COV_E always equals 0.10.
• E_joist_min: Emin (as calculated per NDS Appendix D equation D-4) due to joist/beam loading
• E_plank_min: Emin (as calculated per NDS Appendix D equation D-4) due to plank/flat edge loading

Currently the program only designs using the Joist properties of the SCL materials. This assumes that the loading is always on the small dimension side of the member. In a future version we will be taking the Plank values into consideration as well. In the meantime you can always enter the appropriate design values from these tables as a Custom Wood Material for use in your model.

Custom Wood Sizes

If you would like to enter explicit dimensions of a member or if the member is "Not Dressed", the member must be designated as a "Full Sawn" member by choosing Net Rectangular as the Shape Type and entering the exact dimensions of the member in the boxes below.  This applies to regular wood species, custom wood species, Structural Composite Lumber (SCL), and Glu-Lam members.